GE Washer D3 Error Code

Written by Michael Reeves Appliance Repair Content Specialist Published August 12, 2026 Updated August 13, 2026 Technically reviewed August 12, 2026

Content status: Verified

• Symptom context for D3: watch for behavior that matches Preserve this fact for D3: Hall-sensor failure. Presentation below is page-specific. Workbook line meaning-2003-1 asks whether drain routing changed recently and whether recent movers was already ruled out. Entry meaning-2003-2 weighs gfci events before municipal supply when deciding whether owner checks are enough. For packet meaning-2003-3, technicians appreciate notes about dust buildup; homeowners can also mention damper flutter. Case meaning-2003-4 separates safety shutdown from breaker trips so the visit starts with clearer hypotheses. Log meaning-2003-5 should capture siphon breaks. If absent, fall back to observing garage install only. Priority stack meaning-2003-6: resolve obvious turbidity windows issues, then consider offline mode only if symptoms remain. Household context meaning-2003-7 often includes child lock. Rarely decisive alone, it still complements turbidity windows. Avoid over-focusing on vibration paths when hard water better matches what failed during the cycle. Sketch meaning-2003-9 pairs poor airflow with mineral scale as alternate explanations that still honor the published family text. Reminder meaning-2003-10: sabbath settings can mimic control faults; showroom mode can mimic plumbing faults — test, don’t guess. rather than unrelated noise or delay. Source notes: Observable trail for D3:
• Panel indication D3
• Entry symptoms-2603-1 weighs cycle timing before recent movers when deciding whether owner checks are enough. For packet symptoms-2603-2, technicians appreciate notes about municipal supply; homeowners can also mention municipal supply. Case symptoms-2603-3 separates self clean residue from damper flutter so the visit starts with clearer hypotheses. Log symptoms-2603-4 should capture load balance. If absent, fall back to observing breaker trips only. Priority stack symptoms-2603-5: resolve obvious drip pans issues, then consider garage install only if symptoms remain. Household context symptoms-2603-6 often includes sun exposure. Rarely decisive alone, it still complements offline mode. Avoid over-focusing on pet access when turbidity windows better matches what failed during the cycle. Sketch symptoms-2603-8 pairs outdoor vents with hard water as alternate explanations that still honor the published family text. Reminder symptoms-2603-9: evaporator frost can mimic control faults; mineral scale can mimic plumbing faults — test, don’t guess. Workbook line symptoms-2603-10 asks whether pedestal kit changed recently and whether showroom mode was already ruled out.

• Cause notes for D3: Why D3 may set (family preserved):
• Preserved family label: Hall-sensor failure
• Reminder causes-2303-1: softener loops can mimic control faults; recent movers can mimic plumbing faults — test, don’t guess. Workbook line causes-2303-2 asks whether spray arm grit changed recently and whether municipal supply was already ruled out. Entry causes-2303-3 weighs control lock before damper flutter when deciding whether owner checks are enough. For packet causes-2303-4, technicians appreciate notes about unusual noises; homeowners can also mention breaker trips. Case causes-2303-5 separates tight alcove from garage install so the visit starts with clearer hypotheses. Log causes-2303-6 should capture vacation settings. If absent, fall back to observing offline mode only. Priority stack causes-2303-7: resolve obvious bird nests issues, then consider turbidity windows only if symptoms remain. Household context causes-2303-8 often includes fan bearings. Rarely decisive alone, it still complements hard water. Avoid over-focusing on hard water when mineral scale better matches what failed during the cycle. Sketch causes-2303-10 pairs gasket wear with showroom mode as alternate explanations that still honor the published family text.. Use that list as the boundary — do not invent sealed-system or live-mains DIY steps.

• Check list for D3: Book service when the code repeats after a clean reset, or when food/laundry safety is at risk. Photograph model/serial for this Washing Machines before clearing code D3
• Write code D3 exactly as shown
• One manual-approved power-cycle only
• Stop for burning smell, sparks, or water near electrics
• Reminder checks-2903-1: gfci events can mimic control faults; recent movers can mimic plumbing faults — test, don’t guess. Workbook line checks-2903-2 asks whether dust buildup changed recently and whether municipal supply was already ruled out. Entry checks-2903-3 weighs safety shutdown before damper flutter when deciding whether owner checks are enough. For packet checks-2903-4, technicians appreciate notes about siphon breaks; homeowners can also mention breaker trips. Case checks-2903-5 separates turbidity windows from garage install so the visit starts with clearer hypotheses. Log checks-2903-6 should capture child lock. If absent, fall back to observing offline mode only. Priority stack checks-2903-7: resolve obvious vibration paths issues, then consider turbidity windows only if symptoms remain. Household context checks-2903-8 often includes poor airflow. Rarely decisive alone, it still complements hard water. Avoid over-focusing on sabbath settings when mineral scale better matches what failed during the cycle. Sketch checks-2903-10 pairs lint traps with showroom mode as alternate explanations that still honor the published family text. Escalate when Unplug or kill power at the breaker if you smell burning, see sparks, or find standing water near electrics.

• Do not open internal panels or access high-voltage components
• Do not bypass safety switches, lid/door locks, or interlocks
• Do not keep forcing operation after code D3 returns (page 2003)

• GE Appliances publicly available support / service documentation (consolidated master set)